 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| D100EI Series Low Cost, 1W High Isolation SIP DC/DC Converters Electrical Specifications Specifications typical @ +25C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. New Budget Saver!! Conditions 5 VDC Input 12 VDC Input 24 VDC Input Min. 4.5 10.8 21.6 Typ. 5.0 12.0 24.0 Max. 5.5 13.2 26.4 0.3 Conditions Dual Output , Balanced Loads For Vin Change of 1% Min. Typ. 1.0 0.1 1.2 50 120 0.02 Momentary (1.0 Sec.) Conditions 60 Seconds 500 VDC 100 kHz, 1V 100 Conditions Ambient Case Min. -40 -40 -55 Free Air Convection RH, Non-condensing 95 % Min. 3,000 1,000 60 150 Typ. +25 200 Max. +85 +90 +125 Typ. Max. Units VDC M pF kHz Units C C C 0.03 75 Max. 3.0 1.0 A Units % % % mV P - P % %/C VDC Units Input Key Features: 1W Output Power 3,000 VDC Isolation Miniature SIP Case Single & Dual Outputs >1 MHour MTBF 24 Standard Models LOWEST COST!! Parameter Input Voltage Range Input Filter Reverse Polarity Input Current Internal Capacitor Output Parameter Output Voltage Accuracy Output Voltage Balance Line Regulation Load Regulation (Note 1) Ripple & Noise (20 MHz) (Note 2) Output Power Protection Temperature Coefficient Output Short Circuit See Model Selection Guide General Parameter Isolation Voltage Isolation Resistance Isolation Capacitance Switching Frequency Environmental Parameter Operating Temperature Range Operating Temperature Range Storage Temperature Range Cooling Humidity MicroPower Direct 232 Tosca Drive Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: sales@micropowerdirect.com W: www.micropowerdirect.com Physical Case Size Case Material Weight 0.77 x 0.24 x 0.40 Inches (19.6 x 6.0 x 10.2 mm) Non-Conductive Black Plastic (UL94-V0) 0.07 Oz (2.1g) Conditions MIL HDBK 217F, 25C, Gnd Benign Conditions 5 VDC Input Input Voltage Surge (1 Sec) Lead Temperature Internal Power Dissipation 12 VDC Input 24 VDC Input 1.5 mm From Case For 10 Sec All Models Min. 1.0 Min. -0.7 -0.7 -0.7 Typ. Max. 9.0 18.0 30.0 300 450 C mW VDC Typ. Max. Units MHours Units Reliability Specifications Parameter MTBF Absolute Maximum Ratings Parameter Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. Model Selection Guide Model Number D101EI D102EI D103EI D104EI D105EI D106EI D107EI D108EI D111EI D112EI D113EI D114EI D115EI D116EI D117EI D118EI D121EI D122EI D123EI D124EI D125EI D126EI D127EI D128EI Notes: Input Output Load Fuse Rating Efficiency Voltage (VDC) Current (mA) Slow-Blow Voltage Current Current Regulation (%, Typ) (%, Max) (mA) Nominal Range Full-Load No-Load (VDC) (mA, Max) (mA, Min) 5 4.5 - 5.5 256 30 5.0 200.0 20.0 15 78 500 5 4.5 - 5.5 256 30 9.0 111.0 12.0 15 78 500 5 4.5 - 5.5 250 30 12.0 83.0 9.0 15 80 500 5 4.5 - 5.5 247 30 15.0 67.0 7.0 15 81 500 5 4.5 - 5.5 278 30 5.0 100.0 10.0 15 72 500 5 4.5 - 5.5 267 30 9.0 56.0 6.0 15 78 500 5 4.5 - 5.5 247 30 12.0 42.0 5.0 15 81 500 5 4.5 - 5.5 250 30 15.0 33.0 4.0 15 80 500 12 10.8 - 13.2 107 15 5.0 200.0 20.0 15 78 200 12 10.8 - 13.2 104 15 9.0 111.0 12.0 15 80 200 12 10.8 - 13.2 103 15 12.0 83.0 9.0 15 81 200 12 10.8 - 13.2 104 15 15.0 67.0 7.0 15 80 200 12 10.8 - 13.2 114 15 5.0 100.0 10.0 15 75 200 12 10.8 - 13.2 104 15 9.0 56.0 6.0 15 80 200 12 10.8 - 13.2 103 15 12.0 42.0 5.0 15 81 200 12 10.8 - 13.2 105 15 15.0 33.0 4.0 15 79 200 24 21.6 - 26.4 53 8 5.0 200.0 20.0 15 78 100 24 21.6 - 26.4 53 8 9.0 111.0 12.0 15 79 100 24 21.6 - 26.4 53 8 12.0 83.0 9.0 15 79 100 24 21.6 - 26.4 53 8 15.0 67.0 7.0 15 79 100 24 21.6 - 26.4 58 8 5.0 100.0 10.0 15 72 100 24 21.6 - 26.4 55 8 9.0 56.0 6.0 15 78 100 24 21.6 - 26.4 53 8 12.0 42.0 5.0 15 78 100 24 21.6 - 26.4 52 8 15.0 33.0 4.0 15 80 100 1. Output load regulation is specified for a load change of 10% to 100%. 2. These units should not be operated with a load under 10% of full load. Operation at no-load may cause damage to the unit. 3. These converters will operate without Output Capacitor Input Vin Vout external compoCapacitor Single Dual nents. However, 5 VDC 4.7 F 5 VDC 10.0 F 4.7 F when measuring 12 VDC 2.2 F 9 VDC 4.7 F 2.2 F output ripple, it is recommended that 24 VDC 1.0 F 12 VDC 2.2 F 1.0 F an external ceramic 15 VDC 1.0 F 0.47 F capacitor be placed from the +Vout pin to the -Vout pin for single output units and from each output to common for dual output units. An input capacitor will enhace stability over temperature and input line variations. Recommended capacitor values are given in the table above. For applications requiring very low output noise levels, a simple LC filter should be effective. 4. Dual output units may be connected to provide a 10V, 18V, 24V or 30 VDC output. To do this, connect the load across the positive (+Vout) and negative (-Vout) outputs and float the output common 5. It is recommended that a fuse be used on the input of a power supply for protection. See the Model Selection table above for the correct rating. Derating Curve Mechanical Dimensions Pin Connections Pin 1 2 5 Single +Vin -Vin -Vout Dual +Vin -Vin -Vout Pin 6 7 Single No Pin +Vout Dual Common +Vout Notes: All dimensions are typical in inches (mm) Tolerance x.xx = 0.01 (0.25) Pin 1 is marked by a "dot" or indentation on the side of the unit MicroPower Direct www.micropowerdirect.com 232 Tosca Drive Stoughton, MA 02072 TEL: (781) 344-8226 FAX: (781) 344-8481 E-Mail: sales@micropowerdirect.com |
Price & Availability of D128EI
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |